ثلاثة تطبيقات لللتصميم الكهربائي بنسختها الاصلية مجاناً

ثلاثة تطبيقات للتصميم الكهربائي بنسختها الاصلية مجاناً


نقدم لكم اليوم في هذه التدوينة ثلاثة تطبيقات بنسختها الاصلية للتصميمات والحسابات الكهربائية قيمتها يتجاوز 100 ريال تجدوها مجاناً على مدونة المهندس لتحميل التطبيقات اضغط على الصورة.

1- Electrical Calc Elite Electric

Great for Electrical Contractors, Designers, Engineers, Electricians, Maintenance Inspectors, Planners, Builders, and Lighting Specialists. The Electrical Calc Elite™ allows you to solve code-related problems quickly and accurately...the most common National Electric Code tables are now at your fingertips!
Electrical Calculations
• Wires Sizes
• Voltage Drop on Wires
• Conduit Sizing
• Ohm's Law
• Kirchhoff's Law
• Motor Full-Load Amps
• Power Factor and Motor Efficiency
• Fuse and Breaker Sizes
• Service and Equipment Grounding Sizes
• Electrical Unit conversion
• Parallel Resistance
• Circular MILs Wire
• NEMA starter size
• NEC® references for calculations

2- Electrician Calculator Pro
Electrician Calculator Pro - National Electric Code (NEC) compliant calculator for electricians, engineers and electrical professionals, electrical contractors, designers, lighting experts, inspectors, maintenance personnel and builders!
Compliant with NEC 2014, 2011, 2008, 2005 and 2002, and future updates are FREE!
Forget about complicated key combinations normally required for NEC calculators! With this app you'll be able to perform the following calculations in a straightforward way:
• Voltage Drop
All voltage drop calculations use NEC chapter 9 table 8 values (either stranded or unstranded), and ambient temperature is taken into consideration as per NEC chapter 9 table 8 FPN 2.
• Find voltage drop (in volts and percentage).
• Find the maximum cable length given a required voltage drop and wire gauge (for single and three phase circuits).
• Find the minimum wire gauge given a required voltage drop and distance (for single and three phase circuits).
• Ampacity
Ampacity calculations use NEC tables 310.16 and 310.17 to find maximum ampacity or minimum wire gauge. The correction factor for temperature is used in these calculations.
• Find the minimum wire gauge given an amps value and ambient temperature (can specify if it will be in a raceway or free air).
• Find the maximum ampacity of a cable given its gauge, the ambient temperature, and if it is in a raceway or free air.
• Conduit sizing and conduit fill
Conduit and cable diameters are obtained from the tables in NEC chapter 9. Maximum fill percentages are obtained from NEC chapter 9 table 1.
• Find the minimum size conduit given the gauge and number of cables.
- Can specify the following conduit types: EMT, ENT, FMC, IMC, LFNB, LFNA, RMC, PVC-80, PVC-40 / HDPE, PVC-A, PVC-EB.
- Can specify the following insulation types: THHN, THWN, THWN-2, THW, THHW, THW-2, TW, XHH, XHHW, XHHW-2, RHH, RHW, RHW-2.
• Find the maximum amount of cables that can be used, given conduit size and type, and cable gauge and insulation.
• Motor full load current
Motor full load current values are obtained from NEC tables 430-247, 430-248, 430-250 in chapter 9.
• Find the motor full current load for DC motors, single phase, squirrel cage, wound rotor, and synchronous electrical motors from 1/4HP to 200 HP.
• Grounding conductor
Find the grounding conductor for service entrances and equipment, as per NEC tables 250-66 and 250-122.
• Capacitor KVARs
Find the capacitor KVARs that must be connected to the system in order to correct low power factors caused by inductive loads.
• Power cost
Estimate the financial cost of running a specific load. You enter your KWH rate, the load in KW, and the hours spent with the load connected, and the calculator will return the cost. You can select your own currency from the Preferences section.
                           
3- Electrical Pro


A great tool for electrical engineers and electricians.
This app is a compilation of five sub apps that use the 2008/2011/2014 National Electric Code (NEC).
Bury Depth:
This will calculate the depth needed to bury a line.
Box Conduit Fill Pro:
This will calculate:
The maximum wires in a conduit
The minimum box size
The minimum conduit/nipple size
Fault Calculator Pro:
This will calculate:
A fault over a line
A fault through a XFMR
The bracing de-rate factor for a utility XR ratio
Motor Calculations:
Locked Rotor Amps
NEC Motor Table Look-up
Voltage Drop Pro:
This app will calculate:
The voltage/percent drop for a wire
Minimum wire size for a given percent drop
Max wire length for a given percent drop
Max amps for a given percent drop
The impedance of the wire based on the inputted values
Click the green "Voltage" label for custom voltages
Wire Ampacity Pro:
This app will calculate:
The minimum wire or max amps based on the inputted ampacity for low and medium voltages,
The equipment and service ground size
A residential feeder size
Click the green "Ampacity" label to switch between minimum wire and wire ampacity
Note: This app uses the internet for the Google Licensing Service
This app uses the 2008/2011 NEC to calculate values.
Now you can save initial values to be used in the calculations!
Where length is inputted you can use your GPS from your phone to get an approximate distance (only as accurate as the GPS in your phone).
This app gives you the ability to email the answers calculated to yourself and others.
See the about menu for additional functionality.

اتمنى ان تنال التدوينة اعجابكم ولا تنسوا ان تعملوا مشاركة للموضوع واعجاب بالمدونة ونفخر بتواجدكم معنا.

0 التعليقات:

إرسال تعليق